rigid model

Rigid model of transient analysis for multiple-characteristic long pipelines with trapped air mass

变特性长管道内水流冲击气团的刚性数学模型

Analysis the rigid tie-bar arch bridge power computation model and actual bridge structure different influence, namely computation model rough influence.

通过对刚性系杆拱桥动力计算模型与实际桥梁结构的差异性影响的分析，即计算模型粗糙性的影响。

Chapter 2: Set up a set of models about small transient condition including rigid model including stability and regulation quality and stretch model including pane figure of regulation quality applying to the system of hydropower station with surge tank of many units sharing in one tailrace tunnel.

第2章，建立有调压室的多机一洞水电站小波动的计算模型，包括刚性水击稳定域和调节品质模型及弹性水击调节品质模型方框图。

The principle of motor must be lucubrated. Therefore this thesis makes researches on the stator and rotor coupling rigid model when the generator starts up in frequency conversion. The results can provide theoretical reference to the design of generator.

本文针对变频启动时，电机在电磁激发的定转子耦合刚体模型的振动进行了理论的研究，为电机的可靠性设计提供了理论的参考。

A issues about the orbital modeling of three bodies which are based on ideal rigid body. And therefore give rise to a integrate numerical method of three body problem. The gravity convergence of rigid body is studied based on rigid body model too.

本文讨论了基于理想模型三体轨道运动规律问题，并给出了一个完整的三体问题的数值解决方案；另外还研究了与引力有关的基于刚体模型的天体表面引力收敛问题。

Rigid model for transient flow in pressurized pipe system containing trapped air mass

水流冲击管道内滞留气团的刚性数学模型

The model was validated by the result compare between the rigid extracted from the simulation results and the one out of the rigid test of the leaf spring.

利用模型结果计算钢板弹簧的刚度，并进行钢板弹簧刚度试验验证模型的正确性。

A rigid pushing model based-on 3D thermo-mechanical coupled analysis with FEM was used to simulate wire and rod multi-pass continuous rolling process.

基于三维热-机耦合有限元分析方法建立了刚性体推动模型，模拟棒线材多道次连轧过程。

The classic Pseudo-Rigid-Body Model ( PRBM) can simulate the tip locus of compliant link accurately in a certain extent, but can not simulate the tip deflection angle of the flexible link.

经典的伪刚体模型（Pseudo-Rigid-Body Model，简称PRBM）能较准确地模拟柔顺杆的末端轨迹，但不能模拟柔顺杆的末端转角。

The result is coherent with the result of quantitative physical simulation, numerical value simulation and the tension stress theory of a rigid plastic mechanical model.

结果与定性物理模拟、数值模拟及刚塑性力学模型的拉应力理论相吻合。

Research results: The analysis process of frame bridge with skew angle has been given by use of MIDAS. We obtained the outcomes from two models and the difference between results with 2D rigid frame and 3D space model of thick plate element.

研究结果：给出了用MIDAS分析斜交框架桥的详细分析过程，得出斜交框架桥三维空间模型和二维平面模型分析的结果，并得出2种模型计算结果的差别。

Research on tension stress theory of a rigid plastic mechanical model by optical plastics

用光塑法研究刚塑性力学模型拉应力理论

So the paper introduces Engel coefficient method, increment benefit method and average GNP method into key index of measures, and establishes a comprehensive index model including soft indexes and rigid indexes as well as optimization method to weight every index in the general model.

提出以恩格尔系数法、增量效益分析法与平均GNP法作为关键单指标分析方法，同时建立了包括软指标与硬指标的综合指标评价模型，并给出了估计综合指标评价权重最优赋权法。